10ml HDPE Extrusion Blow Molding Machine MP55D for Potion Bottle
Introduction:
MP55D is specifically designed for making bottles from 5ml up to maximum 1L. It is hydraulic driven with accrate eletrical control system. MP55D has double stations to increase the production efficiency. Also, it has variety of choice of die heads. With more than 10 years of success in the market, MP55D is updated to be one of the most reliable and popular model in the world.
Manual: Push “Manual” key, this machine enters manual state. Under manual state, set all parameter of all action. Setting methods of all parameters are as Computer Operation Manual. Push each action key, finish each action and check its action situation. At the same time, adjust operation pressure, flowrate and position or stroke switch until they are in best situation. Then begin semiautomatic or full automatic operation. This kind of operation mode is probably used during mould test and production beginning stage or used for products which are difficult to be produced automatically. When set to low speed, it can be used during dismantling mould & screw and repairing machine. During operating mechanical action manually, follow action order required by machine.
Pay much attention to lubrication of machine and operate it according to operation requirement strictly. Running in oil starvation will cause wearing to machine (esp. puller bar of mould clamping device) and locking or stop of machine.
Connecting thread area of barrel and head, which are under high temperature, should be coated with lubrication grease (red lead or molybdenum disulfide) for fear of locking during dismantling.
Specifications:
| MP55D |
| Double station blow molder with horizontal linear mould shuttle |
| | | |
| | Length: | 2870mm |
| | Width: | 2140mm |
| | Height: | 2280mm |
| | | |
| Key Data | | MP55D | | |
| | | mm | | |
| Linear mould stroke | A | 380 |  |
| Mould Width | B | 360 |
| Mould Length | C | 300 |
| Mould Thickness | D | 130 |
| Opening Stroke | E | 220 |
| | | | |
| Platen Daylight | D+E | 350 | | |
| Clamping Force | | 30kN | | |
| Centre Distance | 2x2 fold | 130 | | |
| | 2x3 fold | 90 | | |
| | 2x4 fold | 75 | | |
| | 2x5 fold | 60 | | |
| | 2x6 fold | 50 | | |
| | | | | |
| Extruder | | φ55 | φ60 | φ65 |
| Screw Speed | r/min | 0~65 | 0~65 | 0~65 |
| Screw Diameter | mm | 55 | 60 | 65 |
| Screw L/D Ratio | L/D | 24 | 24 | 24 |
| | | | | |
| Energy Requirements | | | | |
| Extruder Inverter Power | kW | 11 | 15 | 18.5 |
| Extruder Moter Power | kW | 11 | 15 | 18.5 |
| Srew Heating Power | kW | 5.85 | 9.4 | 12.3 |
| Fan Power | kW | 0.14X2 | 0.14X2 | 0.14X2 |
| Oil pump Motor Power | kW | 7.5 | 7.5 | 7.5 |
| Total Power of Machine | kW | 33.34 | 40.92 | 47.29 |
| Air Requirement approx | m3/min | 0.8-1 | 0.8-1 | 0.8-1 |
| Air Working Pressure | Mpa | 0.6-0.8 | 0.6-0.8 | 0.6-0.8 |
| | | | | |
| Cooling Requirements | | | | |
| Consumption Cooling Water | L/min | 30 | 30 | 30 |
Product Tags:
|
|
MP55D HDPE Extrusion Double Station Blow Molding Machine For Potion Bottle 10ml Images
|
